How to make Paper Flowers Hollyhock _ Mallows (Flower # 62)

Hi .

Today , I'll be making holly hawks material required is green floral tape , a thick wire for stem thin wire for tying some cotton wool , a red colored pencil and gray paper , double gray paper in pink , white and green .

All the measurements are in centimeter .

This is a stencil of a pattern .

This is 5.5 centimeter long by 4.5 centimeter wide with a stem of one centimeter cut five pieces per floor .

And I have made about six flowers for a stem for a STN strip which is two centimeter wide and 6.5 centimeter long .

This is one piece per floor .

This is a pad cut uh three pieces .

This is 3.5 centimeter long by 4.5 centimeter wide and then a smaller pad which is 2.5 centimeter long by 3.5 centimeter cut three pieces for this also .

Then this is a stencil of a sale .

This is five centimeter wide from here and 3.5 centimeter at the base .

And this is 3.3 centimeter high cut one piece per floor .

This is of a sale which is two centimeter high by 2.5 centimeter wide cut one piece per floor and three pieces for , for three bars .

This is a stencil of a leaf , 2.5 centimeter by five centimeter and the stem is 1.5 centimeter long cut three pieces .

And this is of a bigger leaf .

This is nine centimeters long by 6.5 centimeter wide .

And the stem is two centimeter long cut .

Six pieces , take a smaller but piece and a little bit of the cotton wool , put it in the center and close the sides like this and tie the ends with a uh 6 to 7 inches long thin wire .

I not now take a bit of uh the green floral tape stretch it and then wrap it around the but peace until the end of the war .

Now , uh I've made a part from the bigger piece also and take up a separate piece , small set piece and curl the fringes and apply glue on the base and stick it on the bud , stick it on the base of the pan again .

Take a , a bit of the green floral tape , stretch it and wrap it from the base of the bud till the end of the wire .

Now take a petal and the red colored pencil and color the lower part of the pet give dark strokes so that the color really stands out 10 with your thumbnails and fingernails , just pull the paper between them so that it gives away wavy effect , make this apply glue on a petal starting from the stem and take it up on one side like this and stick the other pedal on it at an angle overlapping it .

So this is how it will look .

And from the back , you can make all that overlap in the first and similarly go on applying blue like this and of course , and stick the petal on it and then do the same for all the five photos .

And this is how it works .

Now take the piece for the steam room .

This has to be cut in white , stretch it and then the very fine cut cuts on it about one sentimental lo almost halfway of the strip .

And this is how they look and this is how it will look .

Leave about two centimeters on one end , don't cut that .

Now take a thin wire , a piece of thin wire about seven inches long , fold it in half like this , apply glue on the paper .

Stay in peace .

Now wrap this on the wire .

So first put it on like this after making a circle , just go down along the wire .

Think so roll in the paper now just to open out the fringes with your fingers .

Who is that apply glue on the petals , first of all semi circle on the pieces and then along side of one petal now put , put the steam and piece in the center just below the fringe first take this part and then stick the other part over overlapping on the last floor .

Last bedroom , stick it and this is how the flow would look .

Now with just hold the petal on the top and stretch it like this in words , all the five petals and this is how the flower would look .

Now take a seven piece , the bigger one like blue on the base and stick this on the base of the flower .

You may have to scrunch the sale a bit where it fits around the floor .

Now take the smallest sale first curl the fringes as we did earlier and then apply glue on the base .

I'll stick this on the base of the first battle was settled .

Take out a small piece from the floral tape , stretch it and wind it from the base of the floor till the end of the wire .

And this is how the flow would look , make about six flowers for the stem , for the leaf , first coat the veins on it .

So with a pair of scissors or anything slightly sharp , just draw lines on it and give a few crims on the edge of the leaf and apply glue on the stem and put the wire , put about two or three inches long wire on it like this and roll the stem around it .

I can take a piece from the floral tape , stretch it and wind this on the stem of the leaf starting from the top , take it down the hole with him .

Now take a long length of the floral tape stretched and it could take a while .

First , take a small bud , hold it onto wire and bind the tape on it and take another bud .

Put it as below the first wind the tape and again , put another bud on the other side slightly lower and win the day .

Then take a bud with the samples .

You put it on the wire and then take a small leaf and put it just below the bud and wrap the tape .

Oh , so do the same for the other two parts .

After putting all the buds , take a flour and put it on the stem , give a few twirls of the tape and then put a leaf below the floor just below the floor and take another flour .

Put it on a slight angle to the first and again , put a leave , put all the flowers like this now just to open out the flowers and the leaves just position them .

The leaves go outwards quite a bit from the stem and the flowers are in an alternate position and the smaller leaves also just open them out even .

And this is held up flower .